Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of HERAFLEX E 4718 1000 NT - TPC - RadiciGroup High Performance Polymers

Material Data Center offers the following functions for HERAFLEX E 4718 1000 NT:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Heraflex E datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Mechanical properties - Thermal properties - Electrical properties - Other properties - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Product Texts
TPC-ET Thermoplastic Elastomer. Low Modulus, Nominal Shore D/15s 43. Natural colou
Mechanical propertiesValueUnitTest Standard
ISO Data
Tensile Modulus 60 MPa ISO 527
Charpy notched impact strength, +23°C N kJ/m² ISO 179/1eA
Stress at 10% elongation 6 MPa ISO 527
Stress at 100% elongation 11 MPa ISO 527
Stress at 300% elongation 12 MPa ISO 527
Tear strength 142 kN/m ISO 34-1
Abrasion resistance 19 mm³ ISO 4649
Shore D hardness 43 - ISO 7619-1
Thermal propertiesValueUnitTest Standard
ISO Data
Melting temperature, 10°C/min 186 °C ISO 11357-1/-3
Temp. of deflection under load, 0.45 MPa 70 °C ISO 75-1/-2
Vicat softening temperature, B 150 °C ISO 306
Electrical propertiesValueUnitTest Standard
ISO Data
Volume resistivity 1E13 Ohm*m IEC 62631-3-1
Other propertiesValueUnitTest Standard
Water absorption 0.45 % Sim. to ISO 62
Density 1150 kg/m³ ISO 1183
Processing Recommendation Injection MoldingValueUnitTest Standard
Pre-drying - Temperature 110 °C -
Pre-drying - Time 2 - 4 h -
Processing humidity ≤0.05 % -
Melt temperature 210 - 220 °C -
Mold temperature 30 - 50 °C -
Characteristics
Processing
Injection Molding, Profile Extrusion
Delivery form
Granules, Natural Color
Regional Availability
North America, Europe, Asia Pacific, South and Central America, Near East/Africa
Other text information
Injection molding
The material is delivered in moisture-proof packaging ready for processing. Maximum recommended water content for best processing is 0.05%. Typical conditions with a desiccant drier: temperature 110 ° C, dew point -30 ° C or below, time 2-4 h or more. Special care must be taken to avoid moisture absorption and contamination with other polymers when adding regrind material. Colour variation and mechanical properties reduction may occur and should always be carefully monitored.

Injection Molding Processing Parameters
Melt TemperatureMold TemperatureInjection Speed
210 - 220°C 30 - 50°Cmedium
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.